No sound on Audirvana with Lynx L22

[Alex13]

Hello,

I have downloaded the free trial verion of Audirvana, when i want to start to play a song with it (on my desktop or with Qobuz) i hav e no sound at all.
The track is loaded but the song doesn’t start stay at 0:00.
I have a asio driver for my Lynx L22 and i have no issue with foobar the sound is OK.

Debug mode:

Audirvana 3.5.5

SIGNAL PROCESSING:

Polarity Inversion:
	Globally: OFF
	Per track: ON
Effects plugins NOT ACTIVE

UPSAMPLING:
SoX not in use
SoX filter parameters
Bandwidth at 0dB = 99.5
Filter max length = 30000
Anti-aliasing = 100
Phase = 66

AUDIO VOLUME:
Max allowed volume: 100
Replay Gain: by track
SW volume control: ON

LIBRARY SETTINGS:
Sync list: 0 folders
Library database path: C:\Users\Alex\AppData\Local\Audirvana\AudirvanaPlus\AudirvanaPlusDatabaseV2.sqlite

ACTIVE STREAMING SERVICES
Qobuz: Connected as Qobuz Studio

=================== AUDIO DEVICE ========================

Max. memory for audio buffers: 3068MB

Local Audio Engine:ASIO 2 driver version 2

Preferred device:
ASIO Lynx
Model UID:ASIO Lynx
UID:ASIO Lynx

Active Sample Rate: 44.1kHz

Bridge settings:
Sample rate limitation: none
Sample rate switching latency: none
Limit bitdepth to 24bit: OFF
Mute during sample rate change: OFF

Selected device:
Local audio device
ASIO Lynx Manufacturer:
Model UID:ASIO Lynx UID:ASIO Lynx

6 available sample rates up to 192000Hz
44100
48000
88200
96000
176400
192000
Volume Control
Physical: No
Virtual: No
MQA capability
Auto-detect MQA devices: No
Not a MQA device, user set to not MQA
DSD capability: Unhandled
Device audio channels
Multichannel: 16 channels
Preferred stereo channels L:0 R:1
Channel bitmap: Ox3, layout:
Channel 0 mapped to 0
Channel 1 mapped to 1
Channel 2 mapped to 2
Channel 3 mapped to 3
Channel 4 mapped to 4
Channel 5 mapped to 5
Channel 6 mapped to 6
Channel 7 mapped to 7
Channel 8 mapped to 8
Channel 9 mapped to 9
Channel 10 mapped to 10
Channel 11 mapped to 11
Channel 12 mapped to 12
Channel 13 mapped to 13
Channel 14 mapped to 14
Channel 15 mapped to 15

Audio channels in use
Number of channels: 16
Use as stereo device only: Yes
Simple stereo device: No

1 output streams:
Number of active channels: 2, in 1 stream(s)
Channel #0 :Stream 0 channel 0
Channel #1 :Stream 0 channel 1
16 ch Integer PCM 32bit little endian 44.1kHz
16 ch Integer PCM 32bit little endian 48kHz
16 ch Integer PCM 32bit little endian 88.2kHz
16 ch Integer PCM 32bit little endian 96kHz
16 ch Integer PCM 32bit little endian 176.4kHz
16 ch Integer PCM 32bit little endian 192kHz

Local devices found : 1
Device #0: ASIO Lynx Manufacturer: Model UID: ASIO Lynx UID: ASIO Lynx

UPnP devices found : 0

Could you help me please ?

Thank you Alex

[Antoine]

Hello @Alex13, are you USB connected to your DAC? Can you try to reconnect it?

[bitracer]

Try using WASAPI. You might have a better luck with it.

[Alex13]

Hello both,

I’m not on USB, it’s a PCI card with XLR symetric connector! I have tried with WASAPI but i have nothing too because there is no driver for it make sense. “Error Message”.

The driver for my card it’s ASIO Only.

When i try to read music with the chipset off the motherboard in SPDIF it’s ok, but i have à low quality on my pre-amplifier than my PCI souncard.

My card works fine with foobar and ASIO but not with audivarna and ASIO. Driver ASIO is the same for both program).

There nothing in settings that i have to change to make it’s works ?

Thank you again for your help!!

Alex

[Alex13]

P.S: Answer to myself to complete my problem.

My card detect the sound but the program doesn’t start the song.foobar|690x462

[Alex13]

[Antoine]

Hello @Alex13, can you go in your audio output in Audirvana and in your ASIO settings unselect “Use large ASIO buffer”?

[Alex13]

Hello @Antoine

Yes i’ve tried to unselect “Use large ASIO buffer” (only on audirvana on my asio) but when i do that the song start but it’s only noise come out like it can’t decrypt the sound.

I don’t know what to do…

Thank you for your help!

[Alex13]

YES i did it,

I change the buffer on my asio preset to the minimum and it’s work perfectly!!

Thank you everyone to help me to fix the problem