Error starting device playback. Again, again and again

Five reboots. Still locked. Pretty pathetic.
Playing a song from library is OK, switching to Qobuz to play a different piece ends up with Error starting device playback.
When it works. songs still stop a few seconds before the end.
Audirvana 3.5.45

SIGNAL PROCESSING:

Polarity Inversion:
	Globally: OFF
	Per track: ON
Effects plugins NOT ACTIVE

UPSAMPLING:
SoX to DSD512 with filter type B 8th order
SoX filter parameters
Bandwidth at 0dB = 90.007
Filter max length = 30000
Anti-aliasing = 100
Phase = 0

AUDIO VOLUME:
Max allowed volume: 100
Replay Gain: None
SW volume control: OFF

LIBRARY SETTINGS:
Sync list: 1 folders
AUTO: E:\backup-003836
Library database path: C:\Users\jeanf\AppData\Local\Audirvana\AudirvanaPlus\AudirvanaPlusDatabaseV2.sqlite

ACTIVE STREAMING SERVICES
Qobuz: Connected as Qobuz Studio

=================== AUDIO DEVICE ========================

Max. memory for audio buffers: 5008MB

Local Audio Engine:ASIO 2 driver version 2

Preferred device:
T+A PDP3000 USB ASIO
Model UID:T+A PDP3000 USB ASIO
UID:T+A PDP3000 USB ASIO

Active Sample Rate: 22579.2kHz

Bridge settings:
Sample rate limitation: none
Sample rate switching latency: none
Limit bitdepth to 24bit: OFF
Mute during sample rate change: ON

Selected device:
Local audio device
T+A PDP3000 USB ASIO Manufacturer:
Model UID:T+A PDP3000 USB ASIO UID:T+A PDP3000 USB ASIO

13 available sample rates up to 45158400Hz
44100
48000
88200
96000
176400
192000
352800
384000
2822400
5644800
11289600
22579200
45158400
Volume Control
Physical: No
Virtual: No
MQA capability
Auto-detect MQA devices: No
Not a MQA device, user set to not MQA
DSD capability: Raw DSD (MSB)
Device audio channels
Preferred stereo channels L:0 R:1
Channel bitmap: Ox3, layout:
Channel 0 mapped to 0
Channel 1 mapped to 1

Audio channels in use
Number of channels: 2
Use as stereo device only: Yes
Simple stereo device: Yes

1 output streams:
Number of active channels: 2, in 1 stream(s)
Channel #0 :Stream 0 channel 0
Channel #1 :Stream 0 channel 1
2 ch Integer PCM 32bit little endian 44.1kHz
2 ch Integer PCM 32bit little endian 48kHz
2 ch Integer PCM 32bit little endian 88.2kHz
2 ch Integer PCM 32bit little endian 96kHz
2 ch Integer PCM 32bit little endian 176.4kHz
2 ch Integer PCM 32bit little endian 192kHz
2 ch Integer PCM 32bit little endian 352.8kHz
2 ch Integer PCM 32bit little endian 384kHz
2 ch DSD 8bit big endian in 8bit chunk 2822.4kHz
2 ch DSD 8bit big endian in 8bit chunk 5644.8kHz
2 ch DSD 8bit big endian in 8bit chunk 11289.6kHz
2 ch DSD 8bit big endian in 8bit chunk 22579.2kHz
2 ch DSD 8bit big endian in 8bit chunk 45158.4kHz

Local devices found : 2
Device #0: T+A PDP3000 USB ASIO Manufacturer: Model UID: T+A PDP3000 USB ASIO UID: T+A PDP3000 USB ASIO
Device #1: TEAC ASIO USB DRIVER Manufacturer: Model UID: TEAC ASIO USB DRIVER UID: TEAC ASIO USB DRIVER

UPnP devices found : 0

Have you tried with upsampling disabled?

Yes. Same issue. Was working almost OK most the time before the update. Still needed to reboot because of the ESSP always present. Now it’s a nightmare. 2 pops in middle of songs then moving to different track, songs not finishing.